Line 13: |
Line 13: |
| On the XO-1, mono data is measured, the left channel, the tip (usually the red wire). The XO-1.5, XO-1.75, XO-3 and XO-4 can read both the left and right channel. (Currently on the XO-1.75, XO-3 and XO-4 stereo input is disabled). | | On the XO-1, mono data is measured, the left channel, the tip (usually the red wire). The XO-1.5, XO-1.75, XO-3 and XO-4 can read both the left and right channel. (Currently on the XO-1.75, XO-3 and XO-4 stereo input is disabled). |
| | | |
− | The XO-1 is protected at the input by a 5V zener diode. The allowable input is -0.5V to 5V. Inputs outside this range will cause excessive current and damage. Even a single 1.5V battery can cause damage if connected reverse polarity. | + | The XO-1 is protected at the input by a 5V zener diode. ([http://wiki.laptop.org/go/File:XO-1_Schematics.pdf 1]) The allowable input is -0.5V to 5V. Inputs outside this range will cause excessive current and damage. Even a single 1.5V battery can cause damage if connected reverse polarity. |
| | | |
− | The XO-1.5 and XO-1.75 (XO-3 and XO-4 presumably too) are protected by a resistor,(1/16W 470 ohm SMD0402) and a pair of diodes to ground and to +3.3V which should protect -6V to +9V continuously, and up to higher voltages for shorter periods of time. | + | The XO-1.5 ( [http://wiki.laptop.org/go/File:XO-1.5_Schematics_rev_G.pdf 2] [http://wiki.laptop.org/go/File:XO-1.5_Schematics_rev_I.pdf 3] [http://wiki.laptop.org/go/File:XO-1.5_Schematics_rev_M.pdf 4] )and XO-1.75 (XO-3 and XO-4 presumably too) are protected by a resistor,(1/16W 470 ohm SMD0402) and a pair of diodes to ground and to +3.3V which should protect -6V to +9V continuously, and up to higher voltages for shorter periods of time. |
| | | |
| For the XO-1, the addition of a 150k ohm series resistor would (I expect, no guarantee) give a reduced sensitivity in voltage mode (0-4V) but allow inputs to +- 100V without damage. Input impedance in resistance, volume and pitch modes is much lower but a 1k ohm series resistor should still allow inputs to +-12V. | | For the XO-1, the addition of a 150k ohm series resistor would (I expect, no guarantee) give a reduced sensitivity in voltage mode (0-4V) but allow inputs to +- 100V without damage. Input impedance in resistance, volume and pitch modes is much lower but a 1k ohm series resistor should still allow inputs to +-12V. |
Line 42: |
Line 42: |
| | | |
| (* A small number of pre-production laptops were built with -3V to +3V input range and input impedance 1k ohm to a +3V bias, eg. model SKU199. Turtle Blocks V141 and previous is correctly calibrated for these laptops but not for production laptops) | | (* A small number of pre-production laptops were built with -3V to +3V input range and input impedance 1k ohm to a +3V bias, eg. model SKU199. Turtle Blocks V141 and previous is correctly calibrated for these laptops but not for production laptops) |
| + | |
| + | ===XO-4=== |
| + | Two channels, 0 to 3V. At the time of writing, as a workaround to a bug with dual channels, apply the input to both channels, only a mono reading is available. |
| | | |
| ==Resistance Mode== | | ==Resistance Mode== |
Line 51: |
Line 54: |
| | | |
| ===XO-1.75=== | | ===XO-1.75=== |
| + | Two channels, zero ohms to open circuit. At the time of writing, as a workaround to a bug with dual channels, apply the input to both channels, only a mono reading is available. |
| + | |
| + | ===XO-4=== |
| Two channels, zero ohms to open circuit. At the time of writing, as a workaround to a bug with dual channels, apply the input to both channels, only a mono reading is available. | | Two channels, zero ohms to open circuit. At the time of writing, as a workaround to a bug with dual channels, apply the input to both channels, only a mono reading is available. |
| | | |