Talk:Downloads: Difference between revisions

Line 61:

* Please note: Software has been updated since that posting. The latest Software is available here:

<code>http://people.sugarlabs.org/bernie/olpc/f11-xo1-py/?C=M;O=D</code>

<big><code>http://people.sugarlabs.org/bernie/olpc/f11-xo1-py/?C=M;O=D</code></big>

* Note: Be sure to plug in your laptop using its AC charger to ensure that the installation process is completed. (The firmware will not be updated under battery power.)

Line 69:

* Connect your device to the OLPC

* Boot while holding down the "checkmark button".

When Open Firmware counts down 3 seconds "...before automatic startup", push the "escape button", to get to the "OK" ~~OpenFirmware~~ prompt.

When Open Firmware counts down 3 seconds "...before automatic startup", push the "escape button", to get to the "OK" Open Firmware prompt.

** If the files were downloaded onto an USB stick:

:* If the files were downloaded onto an USB stick:

type

probe-usb

: {{Code|probe-usb}}

Press Enter.

Control if Open Firmware has detected your device. (A "found" usb when probing, eg usb:/***/disk means u have to name it in the command: copy-nand disk:\os***py.img)

Control if Open Firmware has detected your device. (A "found" usb when probing, e.g., usb:/***/disk means you have to name it in the command: {{Code|copy-nand disk:\os***py.img}})

Then type

copy-nand usb:\os***py.img

: {{Code|copy-nand usb:\os***py.img}}

and press Enter.

(note: replace *** with your actual versionnumber/filename.)

** If the files were downloaded onto a SD card:

:* If the files were downloaded onto a SD card:

type

copy-nand sd:\os***py.img

: {{Code|copy-nand sd:\os***py.img}}

and press Enter.

* when the colored points ~~arent~~ changing anymore and Open Firmware says: OK

* when the colored points aren't changing anymore, and Open Firmware says: OK

disconnect your USB/SD and type

disconnect your USB/SD device and type

reboot

: {{Code|reboot}}

When there happens a failure message (or no at all but no booting-process), try to overwrite your files a second time, try to re-download your file (eg "crc miscompare"), try to reformat your usb-stick (eg "is not a multiple of the nand erase block size"), try googling...

@@ Line 61: / Line 61: @@
 * Please note: Software has been updated since that posting. The latest Software is available here:
-<code>http://people.sugarlabs.org/bernie/olpc/f11-xo1-py/?C=M;O=D</code>
+<big><code>http://people.sugarlabs.org/bernie/olpc/f11-xo1-py/?C=M;O=D</code></big>
 * Note: Be sure to plug in your laptop using its AC charger to ensure that the installation process is completed. (The firmware will not be updated under battery power.)
@@ Line 69: / Line 69: @@
 * Connect your device to the OLPC
 * Boot while holding down the "checkmark button".
-When Open Firmware counts down 3 seconds "...before automatic startup", push the "escape button", to get to the "OK" OpenFirmware prompt.
+When Open Firmware counts down 3 seconds "...before automatic startup", push the "escape button", to get to the "OK" Open Firmware prompt.
-** If the files were downloaded onto an USB stick:
+:* If the files were downloaded onto an USB stick:
 type
- probe-usb
+: {{Code|probe-usb}}
 Press Enter.
-Control if Open Firmware has detected your device. (A "found" usb when probing, eg usb:/***/disk means u have to name it in the command: copy-nand disk:\os***py.img)
+Control if Open Firmware has detected your device. (A "found" usb when probing, e.g., usb:/***/disk means you have to name it in the command: {{Code|copy-nand disk:\os***py.img}})
 Then type
- copy-nand usb:\os***py.img
+: {{Code|copy-nand usb:\os***py.img}}
 and press Enter.
 (note: replace *** with your actual versionnumber/filename.)
-** If the files were downloaded onto a SD card:
+:* If the files were downloaded onto a SD card:
 type
- copy-nand sd:\os***py.img
+: {{Code|copy-nand sd:\os***py.img}}
 and press Enter.
-* when the colored points arent changing anymore and Open Firmware says: OK
+* when the colored points aren't changing anymore, and Open Firmware says: OK
-disconnect your USB/SD and type
+disconnect your USB/SD device and type
- reboot
+: {{Code|reboot}}
 When there happens a failure message (or no at all but no booting-process), try to overwrite your files a second time, try to re-download your file (eg "crc miscompare"), try to reformat your usb-stick (eg "is not a multiple of the nand erase block size"), try googling...