Activities/Turtle Art/Using Turtle Art Sensors

CAUTION. APPLYING EXTERNAL POWER SOURCES TO THE XO LAPTOP'S MICROPHONE INPUT CAN CAUSE PERMANENT DAMAGE. BE SURE YOU READ AND UNDERSTAND THE FOLLOWING BEFORE CONNECTING POWER SOURCES TO YOUR LAPTOP. DO NOT CONNECT TO HAZARDOUS VOLTAGES

Specifications

The OLPC XO can measure external inputs with its microphone jack.

Standard 3.5mm 2-pin switched mono microphone jack; selectable 2V DC bias; selectable sensor-input mode (DC or AC coupled); selectable +20dB boost.

If using a stereo plug it is the tip (usually the red wire) plus the earth.

The XO1 is protected at the input by a 5V zener diode. The allowable input is -0.5V to 5V. Inputs outside this range will cause excessive current and damage. Even a single 1.5V battery can cause damage if connected reverse polarity.

The XO1.5 is protected by a resistor,(1/16W 470 ohm SMD0402) and a pair of diodes to ground and to +3.3V which should protect -6V to +9V continuously, and up to higher voltages for shorter periods of time. Similar protection is planned for the XO1.75.

For the XO1, the addition of a 150k ohm series resistor would (I expect, no guarantee) give a reduced sensitivity in voltage mode (0-4V) but allow inputs to +- 100V without damage. Input impedance in resistance, volume and pitch modes is much lower but a 1k ohm series resistor should still allow inputs to +-12V.

If applying an external voltage to the XO1, it is highly recommended that test leads be made up with a microphone plug and an inbuilt series resistor.

680 ohm series resistor on a 3.5mm audio plug

Test leads with a zener diode and series resistor would expand the safe range for the XO1.5 and XO1.75.

Damage can also be caused by applying voltages between the grounds of any of the external sockets.

Voltage Mode

XO1

Measurement range is DC 0.4V to 1.85V. Voltages less than 0.4V report as 0.4V, voltages greater than 1.85V report as 1.85V. Accuracy is around 3% of full scale. Impedance 140k ohms to a 0.6V bias.

XO1.5

0.17V - 3.0V, impedance 15k ohms to a 1.7V bias.

Resistance Mode

XO1

Measurement range is 750 ohms to 14k ohms, resistances less than 700 ohms report as 700 ohms, greater than 14k ohms report as 14k ohms. Accuracy is around 5% with respect to the full scale voltage measured across the resistor, this translates to round 50 ohms at bottom scale and 2k ohms at top scale. (A series protection resistor of around 700 ohms would give a measurement range of 0 - 13k ohms and protection against +-8V inputs.)

XO1.5

2k ohms to open circuit

Pitch Mode

Pitch Mode is set up for the internal microphone but can also be accessed through the microphone jack, 2V DC bias is on, AC coupled, +20dB boost is on. The frequency of the strongest component is reported in Hz. The resolution is +-8Hz

Sound Mode

Raw data ranging +-32000 XO1, +-10,000 XO1.5. Set up is AC coupled, Bias on, Boost on. Sensitivity is 2uV per unit or 16mV full scale, so sine wave clipping sets in at round 10mV RMS on the XO1. For the XO1.5, sensitivity is approximately 8uV per unit.

With the inbuilt microphone, normal speech is approximately +-1000 XO1 and +-200 XO1.5.

Volume Mode

Ranging 0 to 32000 XO1, 0 to 10,000 XO1.5, set up is for microphone, AC coupled, Bias on, Boost on. Volume is the rectified average of Sound, ie. volume=average(abs(sound))

Graphing the output

Source file as doc File:Oscillo.doc

Measuring Temperature

(For instructions on using the LM35 sensor, see http://wiki.laptop.org/go/Making_XO_sensors/Making_a_Temperature_Sensor)

Connect the TDC05C247 thermistor, Specifications:

• NTC (Negative Temperature Coefficient) Thermistor
• Operating temperature range: -20 Celsius ~ +125 Celsius
• Maximum power rating: 500mW
• Nominal resistance at 25 Celsius 4.7k ohms

Left, the resistance was plotted against temperature and the curve of best fit calculated. Right the blocks convert from resistance to temperature C.

Teaching ideas:

• measure resistance and temperature with a thermometer
• construct your own calibration function
• exponential decay
• diurnal temperature
• heat of reaction, weak acid and base

Measuring Soil Moisture

Two probes into the soil measured in resistance mode. Only a few cm of wire are required to bring soil within the resistance range of the XO1, 700 ohms to 14k ohms

Measuring Water Salinity

Place two copper wires into a glass of water. Experiment with your water and wire diameter, I was able to get a measurement of 5k ohms with 12cm of wire in tank water.

Use the graphing software shown previously but set the turtle y to resistance/50 to scale to the screen size, each 100 on the vertical scale corresponds then to 5000 ohms.

The graph shows first an unconnected circuit (14k ohms) then the circuit is connected. Note how the resistance slowly rises. The terminals are reversed mid screen, the sudden dip and gradual rise are more pronounced. Why is this? Electrolysis products (microscopic bubbles of hydrogen and oxygen for pure water) build up near the electrodes.

Small amounts of salt are added to tank water, bringing the resistance down from 5k ohms to 2k ohms. Salt added on two occasions

Generating Electricity from a Changing Magnetic Field

Requires a refrigerator magnet, often given away free with advertising on it.

Wrap 50 turns of insulated wire onto a nail and connect the two ends to a phono plug as shown (if it is a stereo plug, probably the red wire and the copper shield). Connect the phono plug to the microphone input. Graph the Sound or Volume block. This is better with the XO1 than the XO1.5 because it is more sensitive.

• Wipe the sharp end rapidly over the back of the fridge magnet, try both directions.
• Try a different number of turns of wire
• Try moving the nail more slowly, what happens?
• What is happening?
• Why does it work better on one axis of the magnet? (hint rub 2 magnets together)
• Graph pitch. Explain the result.

Carbon Microphone

Required:

• charcoal
• aluminium foil
• plastic lid
• wire
• rubber band

Crush the charcoal to a fine powder. Make a hole in the centre of the lid. Strip a small amount of insulation from the wire, pass the wire through the hole. Then place a piece of foil against the wire. Fill the lid with crushed charcoal. Place foil over the charcoal and secure with a rubber band. Connect a wire to this foil. Try to get the foil under tension.

Experiment with the fineness of the crushed charcoal and the tension in the foil. The more squashed the charcoal is, the lower the resistance. With the XO1, aim for a resistance of around 3k ohms and definitely 700 ohms < resistance < 14k ohms.

Graph the resistance, pressing on the foil changes the resistance. You have built a pressure sensor. It can also sense air pressure. You have built a microphone. Change to Sound sensing. On my first try I was able to sense clapping.

Lemon battery

See http://en.wikipedia.org/wiki/Lemon_battery

With a copper wire and galvanised nail, the measured voltage is 0.93V, comfortably within the measurement range of the XO1 laptop. The laptop produced negligible loading on the open circuit voltage. With copper wire and an ungalvanised nail the voltage was 0.49V.

The internal resistance of the lemon battery is around 10k ohms, the input impedance of the XO1.5 of 15k ohms introduces considerable error.

Experiment with different materials. Try lemon cells in series.

Door bell / Burglar alarm

Visitors touch the two wires together to ring your door bell. Alternatively, arrange two wires to touch as your door opens.

Here are the Turtle blocks:

The Python Code Block is used to sound an alarm in your loudspeakers.

You need to type the following into Pippy and save to the Journal. Type it exactly as shown, the indents on the last 3 lines are important, for the characters '-l 1' the first is an 'el' and the second a 'one'.

Then in Turtle Art, load the Pippy code into the Python Code Block , then run your program.

Two-tone alarm

Use the following Turtle blocks and Pippy code for a warbling alarm

How it works: the 1000 and 1100 blocks are input x in the Python code. The -f option in speaker-test is the frequency, {0} gets replaced by x which in turn is replaced by 1000 or 1100 so speaker-test is sent either -f 1000 or -f 1100 giving frequencies of 1000 Hz or 1100 Hz.

Measuring AC Amps

An inexpensive current transformer can be built to measure AC amps.

50 turns of insulated copper wire are wrapped on a soft iron bar. Threaded shaft, nuts and another bar complete the magnetic circuit.

Assembled, with optional red heat shrink. The current in the black wire is measured. The 50 turns of fine wire connect to the XO1 in Volume Mode. The maximum is about 15 amps AC before clipping of the AC waveform occurs.

To change sensitivity, vary the number of turns.

Volume measured on XO1, 50 turns of wire.

Measuring power

DO NOT CONNECT TO MAINS POWER. DO NOT WORK NEAR EXPOSED ELECTRICAL CONNECTIONS.

Power = AC Volts x AC Amps x Power Factor

In mains circuits, the voltage is usually known. Typically, power factor is 0.8 or 1.0 depending on the electrical load.

lesson ideas (Spanish)

Importing Logged Data into other Activities

Saving logged data to the clipboard

Logged data can be pushed onto the heap, then when logging is finished, the contents of the heap can be placed onto the clipboard for use in other Activities.

Copy the following code into Pippy

def myblock(lc, x):
    from gtk import Clipboard
    from tautils import data_to_string
    Clipboard().set_text(data_to_string(lc.heap))
  , return

Save to the journal, then in Turtle Art, load the Pippy code into the Python Code Block . When the Python Code Block is executed, the contents of the heap are placed on the clipboard.

Example, import temperatures into Gnumeric spreadsheet

For example, temperatures are logged and then copied to the clipboard. This builds on measuring with a thermistor and the XO1 previously. First load the Pippy code . The temperature is measured and pushed to the heap, then a 5 second delay. This repeats 20 times. Then the contents of the heap are copied to the clipboard.

TurtleArt can be run in Gnome on the XO. The data is then pasted to a Gnumeric spreadsheet. The data is converted text to columns (the Data menu), the leading '[' and trailing ']' are manually deleted, the data is graphed. (Unfortunately, on the XO, the Data, text to columns dialog boxes are off screen, alt f alt f shift tab shift tab shift tab allow conversion of comma separated data.)

Temperature data imported into Gnumeric spreadsheet

Saving logged data to the Journal

The following code File:Saveheaptojournal.doc in the Python Code Block will save the heap as a text file named 'heap' in the Journal. The file 'heap' can then be opened with Write or Edit.

def myblock(lc, x):
    from tautils import get_path, data_to_file
    from sugar.activity import activity
    from gettext import gettext as _
    import os.path
    from sugar.datastore import datastore
    from sugar import profile
    # Save the heap to a file (JSON-encoded)
    heap_file = os.path.join(get_path(activity, 'instance'), 'heap.txt')
    data_to_file(lc.heap, heap_file)
    # Create a datastore object
    dsobject = datastore.create()
    # Write any metadata (specifically set the title of the file
    #                     and specify that this is a plain text file).
    dsobject.metadata['title'] = _('heap')
    dsobject.metadata['icon-color'] = profile.get_color().to_string()
    dsobject.metadata['mime_type'] = 'text/plain'
    dsobject.set_file_path(heap_file)
    datastore.write(dsobject)
    dsobject.destroy()
    return

Logging at regular intervals

The following takes readings at regular intervals, in this case 10 seconds and pushes the result to the heap. For example, use for daily temperature, light, power, noise. Taking readings hourly, quarter hourly etc.

Acceleration on an inclined plane

The XO laptop can be used to do experiments on motion. The XO1.5 is faster and better suited for this. Inexpensive sensor switches can be made of aluminium foil. The switches are 5cm wide to provide an on time which is long enough to measure.

Shown below is a triggerable oscilloscope with calibrated timebase. The logging rate can be increased (Turtle Blocks104) by patching one of the Turtle Art files, talogo.py in directory home/olpc/Activities/TurtleArt.activity/TurtleArt changing self.max_samples from 1500 to 150, This reduces the repeat loop from 15mS to 4mS but there is around 50mS jitter. Datalogging can be done without patching the file, using wide switches and shallow ramps keeps the events within the capability of the XO laptop.

Switches were placed at 20cm, 60cm, 100cm, 140cm, and 180cm along a ramp of length 180cm and height 23cm.

The oscilloscope data is shown below, each square is approximately 200mS

The match between theory and experiment is shown below

Links

• http://wiki.laptop.org/go/Hardware_specification
• http://wiki.laptop.org/go/Talk:Measure
• http://wiki.laptop.org/go/Measure/Hardware
• http://bugs.sugarlabs.org/attachment/ticket/552/sensor%20gain.xls
• http://wiki.laptop.org/go/Making_XO_sensors
• http://lists.laptop.org/pipermail/devel/2010-November/date.html
• http://wiki.laptop.org/go/File:Ext_audio_1.5.png